Printing Network Settings

Use the operation panel to print the machine's current network settings.

Important

• The network settings printout contains important information about your network. Handle it with care.

1. Make sure machine is turned on.

2. Load two sheets of A4 or Letter-sized plain paper.

3. Press and hold Wi-Fi button and release it when ON lamp flashes.

4. Press Wi-Fi button again.

   The machine starts printing network settings information.

   The printed network settings information is as follows:

   Item	Description	Setting
   Product Information	Product information	–
   Product Name	Product name	XXXXXXXX
   ROM Version	ROM version	XXXXXXXX
   Serial Number	Serial number	XXXXXXXX
   Wireless LAN	Wireless LAN	Enable/Disable
   MAC Address	MAC address	XX:XX:XX:XX:XX:XX
   WPS PIN CODE	WPS PIN code	XXXXXXXX
   Infrastructure	Infrastructure	Enable/Disable
   Connection	Connection status	Active/Inactive
   SSID	SSID	Wireless LAN SSID
   Channel *1	Channel	XX (1 to 11)
   Encryption	Encryption method	None/WEP/TKIP/AES
   WEP Key Length	WEP key length (bits)	Inactive/128/64
   Authentication	Authentication method	None/auto/open/shared/WPA-PSK/WPA2-PSK
   Signal Strength	Signal strength	0 to 100 [%]
   TCP/IPv4	TCP/IPv4	Enable
   IP Address	IP address	XXX.XXX.XXX.XXX
   Subnet Mask	Subnet mask	XXX.XXX.XXX.XXX
   Default Gateway	Default gateway	XXX.XXX.XXX.XXX
   TCP/IPv6	TCP/IPv6	Enable/Disable
   IP Address *2	IP address	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Subnet Prefix Length *2	Subnet prefix length	XXX
   Default Gateway *2	Default gateway	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   IPsec *3	IPsec setting	Active
   Security Protocol *3	Security method	ESP/ESP & AH/AH
   Access Point Mode	Access point mode	Enable/Disable
   Connection	Connection status	Active/Inactive
   SSID	SSID	Access Point Mode SSID
   Password	Password	Password of the access point mode (8 to 10 alphanumeric characters)
   Channel	Channel	3
   Encryption	Encryption method	AES
   Authentication	Authentication method	WPA2-PSK
   TCP/IPv4	TCP/IPv4	Enable
   IP Address	IP address	XXX.XXX.XXX.XXX
   Subnet Mask	Subnet mask	XXX.XXX.XXX.XXX
   Default Gateway	Default gateway	XXX.XXX.XXX.XXX
   TCP/IPv6	TCP/IPv6	Enable/Disable
   IP Address *2	IP address	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Subnet Prefix Length *2	Subnet prefix length	XXX
   Default Gateway *2	Default gateway	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   IPsec *3	IPsec setting	Active
   Security Protocol *3	Security method	–
   Other Settings	Other settings	–
   Printer Name	Printer name	Printer name (Up to 15 alphanumeric characters)
   WSD Printing	WSD printing setting	Enable/Disable
   WSD Timeout	Timeout	1/5/10/15/20 [min]
   LPD Printing	LPD printing setting	Enable/Disable
   Bonjour	Bonjour setting	Enable/Disable
   Bonjour Service Name	Bonjour service name	Bonjour service name (Up to 52 alphanumeric characters)
   PictBridge Commun.	PictBridge communication	Enable/Disable
   DNS Server	Obtain DNS server address automatically	Auto/Manual
   Primary Server	Primary server address	XXX.XXX.XXX.XXX
   Secondary Server	Secondary server address	XXX.XXX.XXX.XXX
   Proxy Server	Proxy server setting	Enable/Disable
   Proxy Address	Proxy address	XXXXXXXXXXXXXXXXXXXX
   Proxy Port	Proxy port specification	1 to 65535

   ("XX" represents alphanumeric characters.)

   *1 Channel may range from 1 to 11 depending on country or region of purchase.

   *2 Network status is only printed when IPv6 is enabled.

   *3 Network status is only printed when IPv6 and IPsec settings are enabled.